新聞中心
新聞中心
- 解決羅茨真空泵噪音大的有效方法
- 探秘羅茨風機:如何正確安裝羅茨風機來**魚塘水質?
- 探究羅茨風機客戶常見咨詢問題解析客戶關注的核心問題
- 河道在城鄉發揮著行洪、排澇、灌溉、生態調節、美化環境等重要作
- 問:膜微生物處理水污染技術有什么特性?
- 養殖用羅茨鼓風機的優點總結
- 羅茨真空泵沒進水里,走電問題是造成燒毀的主要素之一
- 羅茨鼓風機維護的綜合檢查方法
- **羅茨風機風壓的方法
- 瑞柘羅茨鼓風機原理與結構簡介
- 問:河道生態治理技術有幾種?分別有什么優缺點???
- 江浙滬羅茨鼓風機供應商簡介
- 污水處理廠運營管理方案(下)
- 污水處理廠運營管理方案(上)
聯系我們
手機:15900463963
電話:400-155-8689
郵箱:
地址:江蘇省蘇州市昆山市
推薦產品
常見問題
羅茨真空泵溫度過高的原因及檢查注意事項
- 作者:超級管理員
- 發布時間:2021-11-24
- 點擊:2353
羅茨真空泵溫度過高的原因
羅茨真空泵工作時,溫度過高容易導致轉子卡死,嚴重時會損壞設備。在這種情況下,我們必須考慮其他情況。造成這種現象的原因有很多。下面介紹一下羅茨真空泵溫度過高的原因。
一、氣流不足。
確保羅茨真空泵的冷卻系統不會被灰塵或污垢堵塞,清潔風扇罩、風扇、通風格柵和冷卻銷,只有確認足夠的通風后才能安裝泵。
二、環境溫度過高,進氣溫度過高。
符合真空泵工作環境溫度范圍要求,符合進氣溫度范圍要求。
三、部分排氣過濾器堵塞。
更換排氣過濾器。
4.油過濾器堵塞(油只能通過旁邊的通道流動,不再過濾)
更換機油濾清器。
5.油箱里的油不夠。
需要加油。
六、油過熱變質。
清洗羅茨真空泵,更換機油過濾器,更換排氣過濾器,注入新油。如果油壽命過長,更換熱絕緣好的油或冷卻系統。
7.電源頻率或電壓超出正常范圍。
提供更穩定的電源。
8.過濾器或過濾網堵塞。進氣、出風口或壓力管道堵塞。
清除堵塞物。
9.進氣、排氣或壓力管直徑過小或管長過長。
更換符合要求的管道。
在羅茨真空泵的運行過程中,應注意羅茨真空泵各部分的溫度升高,以確保循環冷卻水的進出。當真空泵在工作中漏油時,應及時停止工作,并在負壓后進行檢查和維護。在漏油的情況下,真空泵不能繼續運行,做好上述工作,可減少真空泵過熱的次數。
檢查羅茨真空泵時的注意事項
要知道,如果羅茨真空泵定期維護,可以降低設備故障率,使其使用效果不受影響。但是為了保證設備的維護效果,維護時必須注意以下幾點:
1.羅茨真空泵的泵座上不得放置維護工具和任何物體,以保持電機接地線不變。清潔時,注意不要向電機噴水。
二、維修前應處理相關的安全維護程序。
3.切斷電源,釋放剩余液體,切斷入口。出口閥或堵塞的盲板與系統隔離。掛禁動卡。
4.拆卸、清潔、更換零件和維護工具應整齊地放置,以實現文明維護。
5.及時更換羅茨真空泵上的無效密封和其他潤滑部件。
6.油管接頭包裝密封帶、密封線等。;改變不合理的結構和裝置。
因此,在維護羅茨真空泵時,只有更好地維護自己的維護方法是否正確,自己的安全保護措施是否到位,才能更好地保證設備的維護效果。同時,檢查設備附件。零件時,一定要注意自己的維護力,不要用力過猛,以免損壞零件。
Causes of high temperature of Roots vacuum pump
When roots vacuum pump is working, the rotor may be stuck due to high temperature, and the equipment may be damaged in serious cases. In this case, we must consider other situations. There are many reasons for this phenomenon. Here is the reason why the temperature of Roots vacuum pump is too high.
1、 Insufficient air flow.
Ensure that the cooling system of Roots vacuum pump is not blocked by dust or dirt. Clean the fan cover, fan, ventilation grille and cooling pin. Install the pump only after confirming sufficient ventilation.
2、 The ambient temperature is too high, and the intake air temperature is too high.
It meets the requirements of the working environment temperature range of the vacuum pump and the inlet air temperature range.
3、 Some exhaust filters are blocked.
Replace the exhaust filter.
4. the oil filter is blocked (the oil can only flow through the nearby channel and is no longer filtered)
Replace the oil filter.
5. there is not enough oil in the oil tank.
Need to refuel.
6、 The oil is overheated and deteriorated.
Clean roots vacuum pump, replace engine oil filter, replace exhaust filter and inject new oil. If the oil life is too long, replace the thermally insulated oil or the cooling system.
7. the power frequency or voltage exceeds the normal range.
Provide more stable power supply.
8. filter or filter screen is blocked. The air inlet, air outlet or pressure pipe is blocked.
Remove the blockage.
9. the diameter of air inlet, exhaust or pressure pipe is too small or the pipe length is too long.
Replace the pipes that meet the requirements.
During the operation of Roots vacuum pump, pay attention to the temperature rise of all parts of Roots vacuum pump to ensure the inlet and outlet of circulating cooling water. When the vacuum pump leaks oil during operation, it shall stop working in time and conduct inspection and maintenance after negative pressure. In case of oil leakage, the vacuum pump cannot continue to operate. Doing the above work can reduce the times of overheating of the vacuum pump.
Roots vacuum pump
Precautions when checking roots vacuum pump
You should know that if roots vacuum pump is regularly maintained, the equipment failure rate can be reduced, so that its use effect will not be affected. However, in order to ensure the maintenance effect of the equipment, the following points must be paid attention to during maintenance:
1. maintenance tools and any objects shall not be placed on the pump base of Roots vacuum pump to keep the motor grounding wire unchanged. When cleaning, be careful not to spray water on the motor.
2、 Relevant safety maintenance procedures shall be handled before maintenance.
3. cut off the power supply, release the remaining liquid and cut off the inlet. The outlet valve or blocked blind plate is isolated from the system. Hang the immobiliser card.
4. disassembly, cleaning, replacement parts and maintenance tools shall be placed neatly to achieve civilized maintenance.
5. replace the invalid seals and other lubricating parts on Roots vacuum pump in time.
6. oil pipe joint packing sealing belt, sealing line, etc.; Change unreasonable structures and devices.
Therefore, when maintaining roots vacuum pump, only by better maintaining whether the maintenance method is correct and whether the safety protection measures are in place can the maintenance effect of the equipment be better guaranteed. Meanwhile, check the equipment accessories. When using parts, you must pay attention to your own maintenance force. Do not use too much force to avoid damaging parts.
![魯氏羅茨風機-三葉羅茨鼓風機廠家-沉水式鼓風機-[瑞柘環保]](/static/upload/image/20220309/1646805698217314.png)

客服QQ